Fechar
Metadados

1. Identificação
Tipo de ReferênciaArtigo em Revista Científica (Journal Article)
Sitemtc-m21b.sid.inpe.br
Código do Detentorisadg {BR SPINPE} ibi 8JMKD3MGPCW/3DT298S
Identificador8JMKD3MGP3W34P/3HP7R25
Repositóriosid.inpe.br/mtc-m21b/2015/01.13.15.59   (acesso restrito)
Última Atualização2015:01.13.15.59.25 (UTC) administrator
Repositório de Metadadossid.inpe.br/mtc-m21b/2015/01.13.15.59.25
Última Atualização dos Metadados2021:02.11.20.56.35 (UTC) administrator
DOI10.1016/j.expthermflusci.2014.10.002
ISSN0894-1777
Chave de CitaçãoBertoldoJrVlasGenaGued:2015:DyTeMe
TítuloDynamic test method to determine the capillary limit of axially grooved heat pipes
Ano2015
Data de Acesso03 maio 2024
Tipo de Trabalhojournal article
Tipo SecundárioPRE PI
Número de Arquivos1
Tamanho1686 KiB
2. Contextualização
Autor1 Bertoldo Junior, Jorge
2 Vlassov, Valeri Vladimirovich
3 Genaro, Gino
4 Guedes, Ulisses Thadeu Vieira
Identificador de Curriculo1
2
3 8JMKD3MGP5W/3C9JHBG
Grupo1 DMC-ETE-INPE-MCTI-GOV-BR
2 DMC-ETE-INPE-MCTI-GOV-BR
3 DSE-ETE-INPE-MCTI-GOV-BR
4 DMC-ETE-INPE-MCTI-GOV-BR
Afiliação1 Instituto Nacional de Pesquisas Espaciais (INPE)
2 Instituto Nacional de Pesquisas Espaciais (INPE)
3 Instituto Nacional de Pesquisas Espaciais (INPE)
4 Instituto Nacional de Pesquisas Espaciais (INPE)
Endereço de e-Mail do Autor1 jorge.bertoldo@inpe.br
2 valeri.vlassov@inpe.br
3 gino.genaro@inpe.br
4 ulisses.guedes@inpe.br
RevistaExperimental Thermal and Fluid Science
Volume60
Páginas290-298
Nota SecundáriaA2_ENGENHARIAS_III B1_ENGENHARIAS_IV B3_ASTRONOMIA_/_FÍSICA
Histórico (UTC)2015-01-13 16:11:36 :: simone -> administrator :: 2015
2021-02-11 20:56:35 :: administrator -> simone :: 2015
3. Conteúdo e estrutura
É a matriz ou uma cópia?é a matriz
Estágio do Conteúdoconcluido
Transferível1
Tipo do ConteúdoExternal Contribution
Tipo de Versãopublisher
Palavras-ChaveDynamic test method
capillary limit
axially grooved heat pipe
ResumoThe usual experimental method to detect heat pipe capillary limit under different inclinations includes submitting the pipe to a certain tilt and increasing the heat load at the evaporator zone until a sudden rise in temperature at this region (dry out) is observed. According to this method, for each heat load dwell imposed to the pipe, either the dry out phenomenon is detected or steady state temperature is achieved. The complete test is time consuming and the precision of the heat load detection needed to induce the dry out depends on the power step utilized. In addition, sometimes the dry out is difficult to detect accurately in axially grooved heat pipes due to the fact of the liquid phase is distributed in a non-homogeneous way at the evaporator zone. In fact, the grooves at the top of the heat pipe tend to dry faster. At the lower grooves of the evaporator forms a buildup of working fluid (puddle) due to gravitational effects and thus needing a higher heat flux to cause the drying. The dynamic method proposed in this paper to detect dry out in heat pipes consists in applying a given heat load on the heat pipe, which is initially kept in a horizontal position on a rotary table equipped with motor with reducer gearbox and digital inclinometer. After steady state is reached on the heat pipe, which is leveled horizontally, the table is driven causing the pipe to adverse tilt slowly until the dry out occurs. Once dry out initiates, the axial gravity force component, which is permanently increasing due to table rotation, provokes the liquid phase accelerated retreating from the evaporator, including the puddle liquid excess. It assists the fast overheating onset in the dried zone that in its turn allows a very clear detection of the dry out event by a temperature sensor. The pipe is then placed back in the horizontal position. The proposed test method besides requiring less time to obtain the capillary limit curve, permits to detect in a more precision way the exact time when the dry out occurs. The capillary limits obtained from this method were compared against those obtained from conventional methods for ammonia two-core axially-grooved heat pipe. The results show that dynamic test method can be adopted as an effective alternative to determine capillary limit for axially grooved heat pipes.
ÁreaETES
Arranjo 1urlib.net > BDMCI > Fonds > Produção anterior à 2021 > DIDMC > Dynamic test method...
Arranjo 2urlib.net > BDMCI > Fonds > Produção anterior à 2021 > DIDSE > Dynamic test method...
Conteúdo da Pasta docacessar
Conteúdo da Pasta sourcenão têm arquivos
Conteúdo da Pasta agreement
agreement.html 13/01/2015 13:59 1.0 KiB 
4. Condições de acesso e uso
Idiomaen
Arquivo Alvodynamic test.pdf
Grupo de Usuáriosadministrator
simone
Grupo de Leitoresadministrator
simone
Visibilidadeshown
Permissão de Leituradeny from all and allow from 150.163
Permissão de Atualizaçãonão transferida
5. Fontes relacionadas
Repositório Espelhourlib.net/www/2011/03.29.20.55
Unidades Imediatamente Superiores8JMKD3MGPCW/446AF4B
8JMKD3MGPCW/446AUSL
Lista de Itens Citandosid.inpe.br/bibdigital/2021/02.11.18.06 4
sid.inpe.br/mtc-m21/2012/07.13.14.49.26 1
sid.inpe.br/bibdigital/2021/02.11.20.54 1
DivulgaçãoWEBSCI; PORTALCAPES; COMPENDEX; SCOPUS.
Acervo Hospedeirosid.inpe.br/mtc-m21b/2013/09.26.14.25.20
6. Notas
Campos Vaziosalternatejournal archivingpolicy archivist callnumber copyholder copyright creatorhistory descriptionlevel e-mailaddress format isbn label lineage mark month nextedition notes number orcid parameterlist parentrepositories previousedition previouslowerunit progress project rightsholder schedulinginformation secondarydate secondarykey session shorttitle sponsor subject tertiarymark tertiarytype url
7. Controle da descrição
e-Mail (login)simone
atualizar 


Fechar